Magnetism and Electromagnetism Multiple choice Questions
Best Magnetism and Electromagnetism Objective Questions and Answers
Dear Readers, Welcome to Magnetism and Electromagnetism Objective Questions have been designed specially to get you acquainted with the nature of questions you may encounter during your Job interview for the subject of Magnetism and Electromagnetism MCQs. These objective type Magnetism and Electromagnetism Questions are very important for campus placement test and job interviews. As per my experience good interviewers hardly plan to ask any particular question during your Job interview and these model questions are asked in the online technical test and interview of many IT companies.
1. Tesla is a unit of
(a) field strength
(b) inductance
(c) flux density
(d) flux
Ans: c
2. A permeable substance is one
(a) which is a good conductor
(6) which is a bad conductor
(c) which is a strong magnet
(d) through which the magnetic lines of force can pass very easily
Ans: d
3. The materials having low retentivity are suitable for making
(a) weak magnets
(b) temporary magnets
(c) permanent magnets
(d) none of the above
Ans: b
4. A magnetic field exists around
(a) iron
(b) copper
(c) aluminium
(d) moving charges
Ans: d
5. Ferrites are --------- materials.
(a) paramagnetic
(b) diamagnetic
(c) ferromagnetic
(d) none of the above
Ans: c
6. Air gap has_______eluctance as compared to iron or steel path.
(a) little
(b) lower
(c) higher
(d) zero
Ans: b
7. The direction of magnetic lines of force is
(a) from south pole to north pole
(b) from north pole to south pole
(c) from one end of the magnet to another
(d) none of the above
Ans: b
8. Which of the following is a vector quantity ?
(a) Relative permeability
(b) Magnetic field intensity
(c) Flux density
(d) Magnetic potential
Ans: b
9. The two conductors of a transmission line carry equal current I in opposite directions. The force on each conductor is
(a) proportional to 7
(b) proportional to X
(c) proportional to distance between the conductors
(d) inversely proportional to I
Ans: b
10. A material which is slightly repelled by a magnetic field is known as
(a) ferromagnetic material
(b) diamagnetic material
(c) paramag>etic material
(d) conducting material
Ans: b
11. When an iron piece is placed in a magnetic field
(a) the magnetic lines of force will bend away from their usual paths in order to go away from the piece
(b) the magnetic lines of force will bend away from their usual paths in order to pass through the piece
(c) the magnetic field will not be affected
(d) the iron piece will break
Ans: b
12. Fleming's left hand rule is used to find
(a) direction of magnetic field due to current carrying conductor
(b) direction of flux in a solenoid
(c) direction of force on a current car¬rying conductor in a magnetic field
(d) polarity of a magnetic pole
Ans: c
13. The ratio of intensity of magnetisation to the magnetisation force is known as
(a) flux density
(b) susceptibility
(c) relative permeability
(d) none of the above
Ans: b
14. Magnetising steel is normals difficult because
(a) it corrodes easily
(6) it has high permeability
(c) it has high specific gravity
(d) it has low permeability
Ans: d
15. The left hand rule correlates to
(a) current, induced e.m.f. and direc¬tion of force on a conductor
(b) magnetic field, electric field and direction of force on a conductor
(c) self induction, mutual induction and direction of force on a conductor
(d) current, magnetic field and direc¬tion of force on a conductor
Ans: d
16. The unit of relative permeability is
(a) henry/metre
(b) henry
(c) henry/sq. m
(d) it is dimensionless
Ans: d
17. A conductor of length L has current I passing through it, when it is placed parallel to a magnetic field. The force experienced by the conductor will be
(a) zero
(b) BLI
(c) B2LI
(d) BLI2
Ans: a
18. The force between two long parallel conductors is inversely proportional to
(a) radius of conductors
(b) current in one conductor
(c) product of current in two conduc¬tors
(d) distance between the conductors
Ans: d
19. Materials subjected to rapid reversal of magnetism should have
(a) large area oiB-H loop
(b) high permeability and low hysteresis loss
(c) high co-ercivity and high reten-tivity
(d) high co-ercivity and low density
Ans: b
20. Indicate which of the following material does not retain magnetism permanently.
(a) Soft iron
(b) Stainless steel
(e) Hardened steel
(d) None of the above
Ans: a
21. The main constituent of permalloy is
(a) cobalt
(b) chromium
(c) nickel
(d) tungsten
Ans: c
22. The use of permanent magnets is. not made in
(a) magnetoes
(6) energy meters
(c) transformers
(d) loud-speakers
Ans: c
23. Paramagnetic materials have relative permeability
(a) slightly less than uuity
(b) equal to unity
(c) slightly more than unity
(d) equal to that ferromagnetic mate rials
Ans: c
24. Degaussing is the process of
(a) removal of magnetic impurities
(b) removing gases from the materials
(c) remagnetising metallic parts
(d) demagnetising metallic parts
Ans:
25. Substances which have permeability less than the permeability of free space are known as
(a) ferromagnetic
(b) paramagnetic
(c) diamagnetic
(d) bipolar
Ans: c
26. Two infinitely long parallel conductors in vacuum anf' separated 1 metre between centres >rhen a current of 1 ampere flows thn. ugh each conductor, produce on each otLer a force of
(a) 2 x 1(T2 N/m)
(b) 2 x KT3 N/m
(c) 2 x 10"5 N/m
(d) 2x 1(T7 N/m)
Ans: d
27. In the left hand rule, forefinger always represents
(a) voltage
(b) current
(c) magnetic field
(d) direction of force on the conductor
Ans: c
28. Which of the following is a ferromagnetic material ?
(a) Tungsten
(b) Aluminium
(c) Copper
(d) Nickel
Ans: d
29. Ferrites are a sub-group of
(a) non-magnetic materials
(6) ferro-magnetic materials
(c) paramagnetic materials
(d) ferri-magnetic materials
Ans: d
30. Gilbert is a unit of
(a) electromotive force
(6) magnetomotive force
(c) conductance
(d) permittivity
Ans: b
31. The working of a meter is based on the use of a permanent magnet. In order to protect the meter functioning from stray magnetic fields
(a) meter is surrounded by strong magnetic fields
(b) a soft iron shielding is used
(c) a plastic shielding is provided
(d) a shielding of anon-magnetic material is used
Ans: b
32. Reciprocal of permeability is
(a) reluctivity
(b) susceptibility
(c) permittivity
(d) conductance
Ans: a
33. The relative permeability is less than unity is case of
(a) ferromagnetic materials
(b) ferrites
(c) non-ferrous materials
(d) diamagnetic materials
Ans: d
34. Which of the following is the unit of magnetic flux density ?
(a) weber
(b) lumens
(c) tesla
(d) none of the above
Ans: c
35. The magnetism left in the iron after exciting field has been removed is known as
(a) permeance
(b) residual magnetism
(c) susceptance
(d) reluctance
Ans: b
36. Which of the following is not a unit of flux?
(a) Maxwell
(b) Telsa
(c) Weber
(d) All of the above
Ans: b
37. Which of the following is expected to have the maximum permeability ?
(a) Brass
(b) Copper
(c) Zinc
(d) Ebonite
Ans: d
38. One telsa is equal to
(a) 1 Wb/mm2
(b) 1 Wb/m
(c) 1 Wb/m2
(d) 1 mWb/m2
Ans: c
39. Out of the following statements, concerning an electric field, which statement is not true ?
(a) The electric intensity is a vector quantity
(b) The electric field intensity at a point is numerically equal to the force exerted upon a charge placed at that point
(c) An electric field is defined as a point in space at which an electric charge would experienc* a force
(d) Unit field intensity in the exertion of a force of one newton on a charge of one coulomb
Ans: b
40. When a magnet is in motion relative to a coil the induced e.m.f. does not depend upon
(a) resistance of the coil
(b) motion of the magnet
(c) number of turns of the coil
(d) pole strength of the magnet
Ans: a
41. One maxwell is equal to
(a) 10 webers
(b) 10 webers
(c) 10 webers
(d) 10 webers
Ans: d
42. When two ends of a circular uniform wire are joined to the terminals of a battery, the field at the centre of the circle
(a) will be zero
(b) will be infinite
(c) will depend on the amount of e.m.f. applied
(d) will depend on the radius of the circle
Ans: d
43. Susceptibility is positive for
(a) non-magnetic substances
(b) diamagnetic substances
(c) ferromagnetic substances
(d) none of the above
Ans: c
44. Two long parallel conductors carry 100 A. If the conductors are separated by 20 mm, the force per metre of length of each conductor will be
(a) 100 N
(b) 10 N
(c) 1 N
(d) 0.1 N
Ans: d
45. A 300 mm long conductor is carrying a current of 10 A and is situated at right angles to a magnetic field having a flux density of 0.8 T ; the force on the conductor will be
(a) 240 N
(6) 24 N
(c) 2.4 N
(d) 0.24 N
Ans: c
46. A 200 turn coil having an axial length of 30 mm and a radius of 10 mm is pivoted in a magnetic field having a flux density of 0.8 T. If the coil carries a current of 0.5 A, the torque acting on the coil will be
(a) 8 N-m
(b) 0.48 N-m
(e) 0.048 N-m
(d) 0.0048 N-m
[Hint. Torque = 2BIlNr N-m]
Ans: c
47. The electromagnet has 50 turns and a current of 1A flows through the coil. If the length of the magnet circuit is 200 mm, what is the magnetic field strength ?
(a) 2500 AT/m
(b) 250 AT/m
(c) 25 AT/m
(d) 2.5 AT/m
Ans: b
48. What is the magnitude and the direction of force per 1.1m length of a pair of conductors of a direct current linecarrying 10 amperes and spaced 100 mm apart ?
(a) 22 x 10"8 N
(b) 22 x 10"7 N
(c) 22 x 10-6 N
(d) 22 x 10"5 N
Ans: d
49. A square cross-sectional magnet has a pole strength of 1 x 10 Wb and cross sectional area of 20 mm x 20 mm. What is the strength at a distance of 100 mm from the unit pole in air ?
(a) 63.38 N/Wb
(b) 633.8 N/Wb
(c) 6338 N/Wb
(d) 63380 N/Wb
Ans: c
50. The unit of flux is the same as that of
(a) reluctance
(b) resistance
(c) permeance
(d) pole strength
Ans: d
51. Unit for quantity of electricity is
(a) ampere-hour
(b) watt
(c) joule
(d) coulomb
Ans: d
52. The Biot-savart's law is a general modification of
(a) Kirchhoffs law
(b) Lenz's law
(c) Ampere's law
(d) Faraday's laws
Ans: c
53. The most effective and quickest may of making a magnet from soft iron is by
(a) placing it inside a coil carrying current
(b) induction
(c) the use of permanent magnet
(d) rubbing with another magnet
Ans: a
54. The commonly used material for shielding or screening magnetism is
(a) copper
(b) aluminium
(c) soft iron
(d) brass
Ans: c
55. If a copper disc is rotated rapidly below a freely suspended magnetic needle, the magnetic needle shall start rotating with a velocity
(a) less than that of disc but in opposite direction
(b) equal to that of disc and in the same direction
(c) equal to that of disc and in the opposite direction
(d) less than that of disc and in the same direction
Ans: d
56. A permanent magnet
(a) attracts some substances and repels others
(b) attracts all paramagnetic substan¬ces and repels others
(c) attracts only ferromagnetic sub¬stances
(d) attracts ferromagnetic substances and repels all others
Ans: a
57. The retentivity (a property) of material is useful for the construction of
(a) permanent magnets
(b) transformers
(c) non-magnetic substances
(d) electromagnets
Ans: a
58. The relative permeability of materials is not constant.
(a) diamagnetic
(b) paramagnetic
(c) ferromagnetic
(d) insulating
Ans: c
59. The materials are a bit inferior conductors of magnetic flux than air.
(a) ferromagnetic
(b) paramagnetic
(c) diamagnetic
(d) dielectric
Ans: c
60. Hysteresis loop in case of magnetically hard materials is more in shape as compared to magnetically soft materials.
(a) circular
(b) triangular
(c) rectangular
(d) none of the above
Ans: c
61. A rectangular magnet of magnetic moment M is cut into two piece of same length, the magnetic moment of each piece will be
(a) M
(6) M/2
(c) 2 M
(d) M/4
Ans: b
62. A keeper is used to
(a) change the direction of magnetic lines
(b) amplify flux
(c) restore lost flux
(d) provide a closed path for flux
Ans: d
63. Magnetic moment is a
(a) pole strength
(6) universal constant
(c) scalar quantity
(d) vector quantity
Ans: d
64. The change of cross-sectional area of conductor in magnetic field will affect
(a) reluctance of conductor
(b) resistance of conductor
(c) (a) and (b) b >th in the same way
(d) none of the above
Ans: c
65. The uniform magnetic field is
(a) the field of a set of parallel conductors
(b) the field of a single conductor
(c) the field in which all lines of mag¬netic flux are parallel and equidis¬tant
(d) none of the above
Ans: c
66. The magneto-motive force is
(a) the voltage across the two ends of exciting coil
(b) the flow of an electric current
(c) the sum of all currents embraced by one line of magnetic field
(d) the passage of magnetic field through an exciting coil
Ans: c
67. What will be the current passing through the ring shaped air cored coil when number of turns is 800 and ampere turns are 3200 ?
(a) 2
(b) 4
(c) 6
(d) 8
Ans: b
68. What will be the magnetic potential difference across the air gap of 2 cm length in magnetic field of 200 AT/m ?
(a) 2 AT
(b) 4 AT
(c) 6 AT
(d) 10 AT
Ans: b
69. Which of the following statements is correct ?
(a) The magnetic flux inside an exciting coil is lower than its outside surface
(6) The magnetic flux inside an exciting coil is zero
(e) The magnetic flux inside the exciting coil is greater than its outside surface
(d) The magnetic flux inside the exciting coil is same as on its outside surface
Ans: d
70. A certain amount of current flows through a ring-shaped coil with fixed number of turns. How does the magnetic induction B varies inside the coil if an iron core is threaded into coil without dimensional change of coil ?
(a) Decreases
(b) Increases
(c) Remains same
(d) First increases and then decreases depending on the depth of iron in¬sertion
Ans: b
71. The magnetic reluctance of a material
(a) decreases with increasing cross sectional area of material
(6) increases with increasing cross-sec-tional area of material
(c) does not vary with increasing cross-sectional area of material
(d) any of the above
Ans: a
72. The initial permeability of an iron rod is
(a) the highest permeability of the iron rod
(b) the lowest permeability of the iron rod
(c) the permeability at the end of the iron rod
(d) the permeability almost in non-magnetised state
Ans: d
73. How does the magnetic compass needle behave in a magnetic field ?
(a) It assures a position right angle to magnetic field
(b) It starts rotating
(c) It assures a position which follows a line of magnetic flux
(d) None of the above
Ans: c
74. In a simple magnetic field the strength of magnet flux
(a) is constant and has same value in energy part of the magnetic field
(6) increases continuously from initial value to final value
(c) decreases continuously from initial value to final value
(d) first increases and then decreases till it becomes zero
Ans: d
75. The stray line of magnetic flux is defined as
(a) a line vertical to the flux lines
(b) the mean length of a ring shaped coil
(c) a line of magnetic flux in a non-uniform field
(d) a line of magnetic flux which does not follow the designed path
Ans: d
76. The bar magnet has
(a) the dipole moment
(b) monopole moment
(c) (a) and (b) both
(d) none of the above
Ans: a
77. Which of the following materials are dia-magnetic ?
(a) Silver
(b) Copper
(c) Silver and copper
(d) Iron
Ans: c
78. Which of the following type of materials are not very important for engineering applications ?
(a) Ferromagnetic
(b) Paramagnetic
(c) Diamagnetic
(d) None of the above
Ans: c
79. The susceptibility of paramagnetic materials generally lies between
(a) KT3 and 1CT6
(b) 1CT3 and 1CT7
(c) KT4 and KT8
(d) 10"2 and KT5
Ans: a
80. For which of the following materials the saturation value is the highest ?
(a) Ferromagnetic materials
(6) Paramagnetic materials
(c) Diamagnetic materials
(d) Ferrites
Ans: d
81. The magnetic materials exhibit the property of magnetisation because of
(a) orbital motion of electrons
(b) spin of electrons
(c) spin of nucleus
(d) either of these
(e) all of the above
Ans: c
82. For which of the following materials the net magnetic moment should be zero ?
(a) Diamagnetic materials
(b) Ferrimagnetic materials
(c) Antiferromagnetic materials
(d) Antiferrimagnetic materials
Ans: c
83. The attraction capacity of electromagnet will increase if the
(a) core length increases i
(b) core area increases
(c) flux density decreases
(d) flux density increases
Ans: d
84. Which of the following statements is correct ?
(a) The conductivity of ferrites is better than ferromagnetic materials
(b) The conductivity of ferromagnetic materials is better than ferrites
(c) The conductivity of ferrites is very high
(d) The conductivity of ferrites is same as that of ferromagnetic materials
Ans: a
85. Temporary magnets are used in
(a) loud-speakers
(b) generators
(c) motors
(d) all of the above
Ans: d
86. Main causes of noisy solenoid are
(a) strong tendency of fan out of lami-nations at the end caused by repul¬sion among magnetic lines of force
(b) uneven bearing surface, caused by dirt or uneven wear between moving and stationary parts
(c) both of above
(d) none of the above
Ans: c
87. Strength of an electromagnet can be increased by
(a) increasing the cross-sectional area
(b) increasing the number of turns
(c) increasing current supply
(d) all above methods
Ans:
88. Core of an electromagnet should have
(a) low coercivity
(6) high susceptibility
(c) both of the above
(d) none of the above
Ans: c
89. Magnetism of a magnet can be destroyed by
(a) heating
(b) hammering
(c) by inductive action of another magnet
(d) by all above methods
Ans: d