I.C. Engines LAB VIVA Questions & Answers

Best I.C. Engines LAB VIVA Questions and Answers

Dear Readers, Welcome to I.C. Engines LAB VIVA Questions and Answers have been designed specially to get you acquainted with the nature of questions you may encounter during your Job interview for the subject of I.C. Engines LAB VIVA Questions. These I.C. Engines LAB VIVA Interview Questions are very important for campus placement test and job interviews. As per my experience good interviewers hardly plan to ask any particular questions during your Job interview and these model questions are asked in the online technical test and interview of many IT & Non IT Industries.

I.C. Engines LAB VIVA Questions:

1. The constant volume process in I.C. engines is characteristic of the _________.

2. Compression-ignition engines use liquid fuels of _______ volatility.

3. Compression ratio maybe of the order of 11.5 : 1 to 22 : 1 in case of _______.

4. Low CO and hydrocarbon emission occurs at low and moderate loads in case of_______.

5. A triangular rotor rotates on an eccentric shaft inside an epitrochoidal housing, the rotor tips being in constant contact with the housing and form three working chambers.

6. In case of aircraft engines, the power at 6100 m altitude is about_______% of the sea level wide-open throttle output for any given speed.

7. The stroke-bore ratio in case of aircraft engines in normally _________.

8. The spontaneous combustion or autoignition of an appreciable portion of the charge

9. A divided chamber construction, a combination of the precombustion chamber and the turbulence chamber design.

10. Early or late injection of fuel in the diesel engine results in _________.

11. Injection system which forces fuel through spray nozzle by hydraulic pressure.

12. It times, meters and forces the fuel at high pressure through the spray nozzle.

13. A restriction in the outer end of the carburettor to provide an extra rich air-fuel mixture for starting.

14. Used to produce gas-tight seal between the piston and the cylinder liners.

15. It takes care of the fluctuations or the cyclic variations in speed.

16. Closes one end of the cylinder and contains the inlet and exhaust valves.

17. A _______is a device used to diminish noise of the intake or exhaust.

18. The finished part of a shaft which rotates in or against a bearing is called_______.

19. An item made of thin layers.

20. The most effective knock suppressor.

21. Optimum spark advance is the timing which develops maximum

22. Higher concentrations of NO.,, are found in I.C. engines with_______compression ratio.

23. The principal source of exhaust carbon monoxide is_______.

24. Masses used for balancing purposes.

25. A device for atomising and vaporising the fuel and mixing it with air in varying proportions.

26. Used to step up 6 or 12 volts to high tension voltage of about 20 Kvolts.

27. The closed area formed by suction and exhaust operation in I.C. engines.

28. Ratio of brake power to indicated power.

29. The ratio of brake power output to the fuel energy input per unit time _________.

30. The ratio of the mass of the charge admitted during the suction stroke of the engine to the mass at normal pressure and temperature of the volume of the charge equal to piston displacement.

31. Ratio of the indicated thermal efficiency to the corresponding ideal air standard efficiency

32. The ratio of actual fuel air ratio and chemicall correct fuel air ratio.

33. Specific fuel consumption is minimum for fuel air ratio _________.

34. Mean effective pressure is maximum for fuel air ratio _________.

35. The mechanical efficiency of a multicylinder engine is determined by _______test.

36. The four stroke cycle is complete in _______revolutions of crankshaft.

37. For completion of four strokes, the cam shaft makes _______revolution.

38. Only air is sucked in during suction stroke.

39 operation in 4 stroke cycle petrol engine continues from 50° before bottom dead centre to 10° after top dead centre.

40. The thermal efficiency of diesel engine in comparison to petrol engine is ________.

41 _______ is used for obtaining required firing order in spark ignition engines.

42. Petrol engines employ governing.

43. Standard firing order for 4 cylinder petrol engine is _______.

44. Standard firing order for 6 cylinder petrol engine is _______.

45. Morse test is used for multicylinder spark ignition engines to determine

46. Auto-ignition reaction time for petrol-air mixture is minimum for relative fuel air ratio of _______.

47. The tendency to knock in C.I. engines increases with_______the cooling water temperature.

48. Iso-octane in a fuel for spark ignition engines auto ignition.

49. Normal heptane in fuel for spark ignition engines _______auto ignition.

50. The knocking in S.I. engines increases with _______in compression ratio.

51. Advancing the spark timing in S.I. engines _______the tendency for knocking.

52. Tendency to knock in S.I. engines and the cooling water temperature are related.

53. Ignition quality of fuel for S.I. engines is determined by_______number rating.

54. The petrol available commercially in the country has octane number of_______.

55. The diesel available commercially in the country has cetane number of_______.

56. The knocking tendency in C.I. engines increases with ______ of compression ratio.

 

I.C. Engines VIVA Questions & ANSWERS:

1. spark ignition

2. low

3. C.I. engines

4. diesel engines

5. Wankel or rotary engine

6. 50

7. below 1.0

8. combustion knock

9. energy cell

10. loss of power

11. mechanical injection

12. injection pump

13. choke

14. piston rings

15. flywheel

16. cylinder head

17. muffler

18. journal

19. laminated

20. tetraethyl lead

21. torque

22. higher

23. rjch mixture combustion

24. crank webs

25. carburettor

26. ignition coil

27. negative loop

28. mechanical efficiency

29. thermal efficiency

30. charge efficiency

31. relative efficiency

32. relative fuel air ratio

33. less than one

34. greater than one

35. Morse

36. two

37. one

38. diesel engines

39. exhaust

40. higher

41. distributor

42. quantity

43. 1-3-4-2

44. 1-4-2-6-3-5

45. mechanical efficiency

46. unity

47. lowering

48. retards

49. accelerates

50. increase

51. increases

52. directly

53. octane

54. 80-85

55. 40-45

56. decrease